features low cost this series is ul recognized under component index, file number e127707 high forward surge current capability low thermal resistance. high isolation voltage from case to lugs. high temperature soldering guaranteed: 260 /10 second, at 5 lbs. (2.3kg) tension. mechanical data case: molded body terminal: plated 0.25" (6.35mm) lug. polarity: polarity symbols marked on case. mounting: thru hole for #10 screw, 20 in - lbs. torque max weight: 0.62ounce, 17.5gram(br40) maximum ratings and electrical characteristics ratings at 25 ambient temperature unless otherwise specified single phase, half wave, 60hz, resistive or inductive load. for capacitive load derate current by 20% symbols br5005 br501 br502 br504 br506 BR508 br5010 v rrm volts maximum rms voltage v rms
volts maximum dc blocking voltage v dc volts maximum average forward rectified output current, at t c = 50 (note1,2) peak forward surge current 8.3ms single half sine - wave superimposed on rated load (jedec method ) rating for fusing (t<8.3ms) i 2 ta 2 s per bridge element at 25a maximum dc reverse current at rated t a = 25 amp dc blocking voltage per element t a
mamp isolation voltage from case to lugs v iso v ac typical thermal resistance (note 1, 2) r jc /w operating temperature range t j storage temperature range t stg 1. unit mounted on 9" x 3.5" x 4.6" (23 x 9 x 11.8cm) al. finned plate. 2. bolt down on heatsink with silicon thermal compound between bridge and mounting surface for maximum heat transfer efficiency with #10 screw. single-phase bridge rectifier amps maximum repetitive peak reverse voltage (-65 to +150) amps volts (-65 to +150) i (av) maximum instantaneous forward voltage drop v f i r i fsm br 5005-5010 http:// www.wej.cn e-mail:wej@yongerjia.com wej electronic co. r o hs wej electronic co.,ltd
average power dissipation of bridge, average output current, 0 50 20 (w) 40 60 80 2010 15 30 25 or resistive load inductive 35 j j max load capacitive t =t per bridge lement fig.3-typical forward characteristics 1%duty cycle pulse width=300us 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 inductive or resistive fig.1-derating curve for case temperature, ( c) output rectified current instantaneous forward voltage,(v) instantaneous forward current, 0.01 0.1 (a) 1.0 100 10 average forward output 0 0 50 30 current,(a) half wave 60hz single phase load 50 percent of rated peak reverse voltage,(%) 40 fig.5-maximum power dissipation instantaneous reverse current, 100 0.01 0 20 0.1 j t =25 c (ua) 1.0 10 100 100 60 80 120 140 j t =25 c j t =100 c fig.4-typical reverse characteristics forward surge current per element number of cycles at 60 hz fig.2-maximum non-repetitive peak 500 peak forward surge current, (a) 125 2 1 0 4 400 200 100 300 1 cycle heat sink mounting 600 700 6 8 10 20 40 60 100 t 8.3ms single half sine-wave (jedec method) =t j j max 9"x 3.5"x 4.6" thick (23 x 9 x 11.8cm) al.finned plate 2-56 per bridge element 25 75 100 150 175 (a) 10 40 45 50 br 5005-5010 http:// www.wej.cn e-mail:wej@yongerjia.com wej electronic co. r o hs wej electronic co.,ltd
|
